 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ILA1519 2 x 6 Watt Stereo Car Radio Power Amplifier GENERAL DESCRIPTION The ILA1519B is an integrated class-B dual output amplifier in a 9-lead single in-line (SIL) plastic medium power package. The device is primarily developed for car radio applications. FEATURES Requires very few external components Thermally protected High output power Reverse polarity safe Fixed gain Compatible with TDA1517 (except gain) Good ripple rejection No switch-on/switch-off plop Mute/stand-by switch Protected against electrostatic discharge Load dump protection AC and DC short-circuit-safe to ground and Vp Capability to handle high energy on outputs (Vp = 0 V) QUICK REFERENCE DATA PARAMETER Supply voltage range operating non-operating load dump protected Repetitive peak output current Total quiescent current Stand-by current Switch-on current Input impedance Output power Channel separation Noise output voltage Supply voltage ripple rejection Crystal temperature CONDITIONS SYMBOL Vp Vp Vp IORM Itot Isb Isw /Z1/ THD= 0,5%;4 THD=10%;4 Vno(rms) SVRR SVRR Tc 40 150 40 48 150 MIN. 6,0 TYP. 14,4 40 0,1 50 5 6 MAX. 18,0 30 45 2,5 80 100 40 UNIT V V V A mA mA mA k W W dB V dB dB 0 C f=100Hz f=1kHz to 10 kHz PACKAGE OUTLINE: 9-lead SIL-bent-to-DIL; plastic (SOT110B). PINNING 1 2 3 4 5 6 7 8 9 NV1 GND1 SVRR OUT1 GND2 OUT2 Vp M/SS INV2 non-inverting input 1 ground (signal) supply voltage ripple rejection output 1 ground (substrate) output 2 supply voltage mute/stand-by switch non-inverting input 2 1 INTEGRAL ILA1519 DC CHARACTERISTICS (note 1) Vp = 14,4 V; Tamb = 25 C; unless otherwise specified PARAMETER CONDITIONS Supply Supply voltage range note 2 Quiescent current note 3 DC output voltage Mute/stand-by switch Switch-on voltage level Mute condition Output signal in mute position o SYMBOL Vp IP VO MIN. 6,0 - TYP. 14,4 40 6,95 MAX. 18,0 80 - UNIT V mA V see Fig.3 VON Vmute VI = 1 V (max.); f = 20 Hz to 15 kHz VO Vsb Isb Isw 8,5 3,3 0 12 20 2 100 40 mV V A A 6,4 V V Stand-by condition DC current in stand-by condition Switch-on current AC CHARACTERISTICS (note 1) Vp=14,4V; RL=4; f=1kHz; Tamb=25 C unless otherwise specified parameter conditions symbol Output power note 4; PO THD = 0,5% PO THD = 10% Total harmonic distortion THD PO=1W Low frequency roll-off note 5; -3 dB fL fH High frequency roll-off -1 dB GV Closed loop voltage gain Supply voltage ripple rejection note 6 ON f= 100 Hz SVRR ON f= 10 Hz to 10 kHz SVRR SVRR mute SVRR stand-by lZil Input impedance note 7; Noise output voltage Vno(rms) ON RS=0 Vno(rms) ON RS= 10 k Vno(rms) a mute note 8 lDGvl Channel separation RS= 10 k Channel balance o min. 4 5,5 20 39 typ. 5 6,0 0,1 45 40 max. 41 unit W W % Hz kHz dB 40 48 48 80 50 40 - 60 150 250 120 0,1 75 500 1 dB dB dB dB k mV mV mV dB dB Notes to the characteristics 1. All characteristics are measured using the circuit shown in Fig. 4. 2. The circuit is DC adjusted at Vp= 6V to 18V and AC operating at Vp= 8,5V to 18 V. 3. At 18 V < Vp< 30 V the DC output voltage < Vp/2. 4. Output power is measured directly at the output pins of the IC. 5. Frequency response externally fixed. 6. Ripple rejection measured at the output with a source impedance of 0 ^ (maximum ripple amplitude of 2 V) and a frequency between 100 Hz and 10 kHz. 7. Noise voltage measured in a bandwidth of 20 Hz to 20 kHz. 8. Noise output voltage independent of R^ (V j = 0 V). 2 INTEGRAL |
Price & Availability of ILA1519
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |